af-packet:
  - interface: enp2s0
    # Number of receive threads. "auto" uses the number of cores
    threads: 2
    # Default clusterid. AF_PACKET will load balance packets based on flow.
    cluster-id: 52
    # Default AF_PACKET cluster type. AF_PACKET can load balance per flow or per hash.
    # This is only supported for Linux kernel > 3.1
    # possible value are:
    #  * cluster_round_robin: round robin load balancing
    #  * cluster_flow: all packets of a given flow are send to the same socket
    #  * cluster_cpu: all packets treated in kernel by a CPU are send to the same socket
    #  * cluster_qm: all packets linked by network card to a RSS queue are sent to the same
    #  socket. Requires at least Linux 3.14.
    #  * cluster_random: packets are sent randomly to sockets but with an equipartition.
    #  Requires at least Linux 3.14.
    #  * cluster_rollover: kernel rotates between sockets filling each socket before moving
    #  to the next. Requires at least Linux 3.10.
    #  * cluster_ebpf: eBPF file load balancing. See doc/userguide/capture-hardware/ebpf-xdp.rst for
    #  more info.
    # Recommended modes are cluster_flow on most boxes and cluster_cpu or cluster_qm on system
    # with capture card using RSS (require cpu affinity tuning and system irq tuning)
    cluster-type: cluster_flow
    # In some fragmentation case, the hash can not be computed. If "defrag" is set
    # to yes, the kernel will do the needed defragmentation before sending the packets.
    defrag: yes
    # After Linux kernel 3.10 it is possible to activate the rollover option: if a socket is
    # full then kernel will send the packet on the next socket with room available. This option
    # can minimize packet drop and increase the treated bandwidth on single intensive flow.
    #rollover: yes
    # To use the ring feature of AF_PACKET, set 'use-mmap' to yes
    #use-mmap: yes
    # Lock memory map to avoid it goes to swap. Be careful that over subscribing could lock
    # your system
    #mmap-locked: yes
    # Use tpacket_v3 capture mode, only active if use-mmap is true
    # Don't use it in IPS or TAP mode as it causes severe latency
    #tpacket-v3: yes
    # Ring size will be computed with respect to max_pending_packets and number
    # of threads. You can set manually the ring size in number of packets by setting
    # the following value. If you are using flow cluster-type and have really network
    # intensive single-flow you could want to set the ring-size independently of the number
    # of threads:
    #ring-size: 2048
    # Block size is used by tpacket_v3 only. It should set to a value high enough to contain
    # a decent number of packets. Size is in bytes so please consider your MTU. It should be
    # a power of 2 and it must be multiple of page size (usually 4096).
    #block-size: 32768
    # tpacket_v3 block timeout: an open block is passed to userspace if it is not
    # filled after block-timeout milliseconds.
    #block-timeout: 10
    # On busy system, this could help to set it to yes to recover from a packet drop
    # phase. This will result in some packets (at max a ring flush) being non treated.
    #use-emergency-flush: yes
    # recv buffer size, increase value could improve performance
    # buffer-size: 32768
    # Set to yes to disable promiscuous mode
    # disable-promisc: no
    # Choose checksum verification mode for the interface. At the moment
    # of the capture, some packets may be with an invalid checksum due to
    # offloading to the network card of the checksum computation.
    # Possible values are:
    #  - kernel: use indication sent by kernel for each packet (default)
    #  - yes: checksum validation is forced
    #  - no: checksum validation is disabled
    #  - auto: suricata uses a statistical approach to detect when
    #  checksum off-loading is used.
    # Warning: 'checksum-validation' must be set to yes to have any validation
    #checksum-checks: kernel
    # BPF filter to apply to this interface. The pcap filter syntax apply here.
    #bpf-filter: port 80 or udp
    # You can use the following variables to activate AF_PACKET tap or IPS mode.
    # If copy-mode is set to ips or tap, the traffic coming to the current
    # interface will be copied to the copy-iface interface. If 'tap' is set, the
    # copy is complete. If 'ips' is set, the packet matching a 'drop' action
    # will not be copied.
    #copy-mode: ips
    #copy-iface: eth1
    #  For eBPF and XDP setup including bypass, filter and load balancing, please
    #  see doc/userguide/capture/ebpf-xdt.rst for more info.
    #  For eBPF and XDP setup including bypass, filter and load balancing, please
    #  see doc/userguide/capture/ebpf-xdt.rst for more info.

  # Put default values here. These will be used for an interface that is not
  # in the list above.
  - interface: default
    threads: 2
    #use-mmap: no
    #rollover: yes
    #tpacket-v3: yes